<div dir="ltr"><div><div><div><div><div><div><div><div><div><div><div><div><div><div><div><div><div><div><div><div><div><div>Dear people:<br><br></div>I'm extremely grateful for TeXLive. However, I would really like that,if possible, you make the TeXLive Windows installers fail more gracefully.<br><br></div><div>tl; dr version: TeXLive Windows managers/installers cannot resume a failed install/update. This is awful taking into account the enormous amount of time required to finish an install/update. Please make them more fail tolerant.<br><br></div><div>Long version:<br></div><div><br></div><div>Background. I usually use TeXLive packaged by my desktop Linux distribution.<br></div><br></div>However, my PC started developing an annoying condition that makes it turn off with little or no warning. The only mitigation (while some parts are shipping) is to use Windows. This is because the manufacturer has a sensor suite for Windows which give me a warning of some seconds before the computer turns itself off. There I could poke the machine, restore the working part (for some minutes) and avoid the shutdown.<br><br></div>However, some times I miss and then the computer turns itself off.<br><br></div>Extremely annoying, as you might imagine. <br><br></div>However, there is impending work that needs to be done. Since I need to use Windows, I downloaded TexLive 2017 in its ISO image (the netinstall would have me hooked for over 7 hours).<br><br></div>OK. Enough background.<br><br></div>The issue is: I installed TeXLive from the 2017 ISO image.<br></div>The process took me about 2.5 hours and this is in a fast, i7 system with a SSD drive.<br></div><div> The point is: there is a lot of data and therefore it takes a lot of time. <br></div><div><br></div>After that, I switched to a net repository and began updating the packages. There are a lot of packages to be updated, as you might know since we are nearing the 2018 release.<br><br></div>The process took over 3 hours and it was getting around packages beginning with the "p" letter when my computer turned itself off due to circumstances explained in the background.<br><br></div>Turned back on, started the TexLive Manager and... it was unusable. "Cannot determine version!" was the only message.<br><br></div>Take into account that all packages were OK in the installation directory, save for perhaps the package which was being updated at the time. Thus, TeXLive Manager should have been able to pick up from the "last known good update" and resume from there.<br><br></div>However, since it did not, this is what happened:<br></div>1. Made me reinstall the whole TeXLive 2017; and<br></div>2. Then I am scheduled to reupdate again.<br><br></div>And if the TexLive installer fails, it's the same. Zero chances to resume from the "last known good" package or whatever. It's the whole 2.5 hours again.<br><br></div>Please bear in consideration that the install time for a reasonably complete TeXLive texmf setup is really long. Whenever long times are involved, chances of failure increase. Therefore, it is highly advisable to make the installer and TeXLive Manager more fault tolerant and able to resume from an interrupted previous process. <br><br></div>Please do that!<br><br></div>Thanks and best regards,<br><br><br></div>Eduardo Sánchez<br></div>Asunción, Paraguay<br clear="all"><div><div><div><div><div><div><div><div><div><div><div><div><div><div><div><div><div><div><div><div><div><div><div><div><div><div><div><br></div></div></div></div></div></div></div></div></div></div></div></div></div></div></div></div></div></div></div></div></div></div></div></div></div></div></div></div>